Operator at a welding fixture with a rack of stored fixtures, an example of turret and fixture management in a fabrication shop

Author: Andrew Holmes in: Fabricated Metals
New Features

November 18, 2026

Turret and Fixture Management: What Poor Tracking Costs and What Good Looks Like

Ask a supervisor why a run produced a sheet of burred parts and you often hear the same story. The punch in station 12 was past its life, nobody knew, and the first sign was the scrap on the cart. The same story plays out with fixtures wearing out of tolerance while they keep holding parts.

Most fabrication shops track tool and fixture life with a mix of tribal knowledge, whiteboards, and the memory of whoever has run the machine longest. This post covers what poor turret and fixture management costs, what good management looks like, and what OnRamp added most recently to make the maintenance team’s job easier.

Where Tool and Fixture Knowledge Lives Today

In many shops the real tool life record sits in one or two heads. The operator knows a punch is getting dull, the tool room guesses when it was last sharpened, and the schedule decides whether anyone acts on either. This holds until the person with the memory is out, a hot job jumps the line, or a new operator takes over the machine, and then tool changes happen after a problem instead of before.

What Poor Turret and Fixture Management Costs

The cost shows up in three places, and none of them appears on the monthly report as a tooling problem.

  • Worn tools and fixtures produce scrap and rework, because burrs, out-of-spec features, and poor location show up downstream on parts the shop already cut.
  • Replacements happen in a rush, which means machines sit idle while someone hunts for a sharpened tool or a good fixture.
  • The tool room reacts to complaints, so sharpening follows problems instead of preventing them.

Underneath all three, the shop depends on knowledge held by a few people, and production stalls when they are out.

What Good Looks Like

A shop with this under control knows which tools and fixtures each part needs before the job reaches the machine. It records usage as work gets done instead of asking operators to log it, so nobody relies on a guess about tool life. The shop sets a usage limit for each tool and fixture, and the team responsible for replacements hears about an item nearing its limit before it causes a bad run. Operators receive sharpened tools in the bin at the machine, and the record of what sits in each turret station matches what is physically in the machine.

Multi-torch cutting table processing nested parts from steel plate in a sheet metal fabrication shop

How OnRamp Tracks Tool and Fixture Life

OnRamp already handles the first half of this. In part master, you list the tools and fixtures each part uses and set a usage limit on each one, after which it should be changed out. As operations on a work order are reported, OnRamp captures tool and fixture usage automatically, so consumption builds up without anyone logging it by hand and replacement timing becomes easier to plan.

Operator loading sheet metal into a stamping die with a tool ID tag, showing tool life tracking on a fabrication shop floor

What Is New for Turrets

The most recent enhancement targets turret tooling and focuses on getting usage and replacement needs in front of the maintenance team, or whoever manages tooling, without anyone asking for them. OnRamp delivers those needs through scheduled reports, automated email and in-app notifications, and dashboard widgets, so each person sees them in the place they already work.

  • Weekly replacement report: OnRamp runs this as a scheduled report listing every turret tool over its maximum hit count, grouped by work center with each work center on its own page, so the tool room preps one bin of sharpened tools per machine.
  • Notifications: automated email and in-app notifications tell the maintenance team when tools reach their limits, so replacements do not wait for the weekly report or a phone call.
  • Dashboard widgets: a tooling manager keeps tool life and upcoming replacements on a dashboard and checks status at any point in the day.
  • Replacement confirmation: at the machine, the operator sees the live list of overdue tools for the work center, swaps in the sharpened tools, and confirms, and OnRamp resets the hit counts.
  • Setup guidance: after the operator scans the scheduled nest, a Nest Tooling tab shows only the tool changes the program requires, such as “Station 4 currently contains Tool A. Replace it with Tool B.” Stations already correct stay off the screen, and Confirm Turret Setup updates the recorded turret configuration for the next nest.
  • Turret configuration: your team enters what each turret holds on day one and corrects any station where the record drifts from the machine.

OnRamp keeps the two confirmations separate on purpose. A tool changed for a program often needs replacing for wear at the same time, but confirming a setup never resets hits and confirming a replacement never changes station assignments, so each record stays accurate.

What Changes for the Maintenance Team

The tool room stops waiting on phone calls and complaints. The weekly report, the email and in-app notifications, and the dashboard widgets tell them what is due and where it goes, tools come out before they reach end of life, and operators spend less time hunting for the right tool. Supervisors spend less time on the floor settling setup questions, and the knowledge of what sits in each turret and how much life each tool has left lives in OnRamp instead of in one person’s memory.

If your tool and fixture tracking still runs on whiteboards and memory, send us a few of your parts and their tool lists and we will show you how they run in OnRamp.

pattern

Let Our Experts Answer Your Questions

For more information about how OnRamp ERP software can add value to your business fill in the contact form below. A member of our support team will contact you within 1 business day to discuss any questions you have.






    or call us now!
    +1 (905) 901-5020

    Start the collaboration with us while figuring out the best solution based on your needs.

    Head Office : 10114 ON-26 Unit 2, Collingwood, ON L9Y 3Z1 , info@onramp-solutions.com
    Location Icon
    View on Google map

    Unlock your Free ERP Readiness Checklist

    Has your business outgrown a patchwork of disconnected systems? This checklist helps you assess readiness, identify gaps, and prepare for a smooth transition.